 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MLX90808 Absolute Integrated Pressure Sensor Features and Benefits Absolute Integrated Pressure sensor Less than 1% error range overall Programmable through the connector (3 pins) Trimmable offset and sensitivity Ratiometric output Rail-to-Rail output Output proportional to the applied pressure Diagnostics of broken supply wires and broken sensor Output protected against short-circuits at both battery terminals On-chip Signal Conditioning (single die solution) Different pressure ranges available Application Examples Automotive applications (MAP, T-MAP, HVAC, ...) Industrial applications Barometric Air Pressure Ordering Information Part No. MLX90808 Temperature Suffix L (-40 to 150C) C Package Code UF (die on foil) Option -2 Description 3 to 7 Bar Pressure Span 1 Functional Diagram 2 General Description The MLX90808 is an integrated absolute pressure sensor realised in CMOS technology. It consists of an analog signal chain that interacts with the digital core and on-chip temperature sensor in order to provide uniform overall sensing characteristics after calibration and to cancel the temperature related parameter drifts. The output is proportional to the applied pressure with an adjustable slope and offset. The chip is ratiometric and goes rail-to-rail with a 1mA source and sink capability. 3901090808 Rev 001 Page 1 of 8 Data Sheet Feb 08 MLX90808 Absolute Integrated Pressure Sensor Table of Contents 1 Functional Diagram........................................................................................................... 1 2 General Description .......................................................................................................... 1 3 Absolute Maximum Ratings .............................................................................................. 3 4 General Electrical Specifications....................................................................................... 3 5 Diagnostic features ........................................................................................................... 4 6 Detailed General Description ............................................................................................ 4 7 Unique Features ............................................................................................................... 5 8 Application Information ..................................................................................................... 5 9 Programming and Calibration ........................................................................................... 6 9.1 Programming of the Temporary Memory of 90808 ..................................................... 6 9.2 Zapping of the 90808 .................................................................................................. 7 10 Disclaimer ....................................................................................................................... 8 3901090808 Rev 001 Page 2 of 8 Data Sheet Feb 08 MLX90808 Absolute Integrated Pressure Sensor 3 Absolute Maximum Ratings Symb ol Supply Voltage (overvoltage) VDD Supply Voltage (operating) VDD Supply Current, IDD with VDD = 16 V IDD Output Voltage, Vout Vout Supply current with output shorted to 0V .. 16V IDD Supply Current limit, reverse polarity IDD Programming Temperature Range (ZAP cells) TP Operating Temperature Range TA Storage Temperature Range TS ESD Sensitivity (AEC Q100 002) Table 1: Absolute maximum ratings Parameter Min Value -14 4.5 -0.5 Max Value 16 5.5 25 16 100 160 100 140 150 2 Units V V mA V mA mA C C C kV -20 -40 - 50 -2 Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute-maximumrated conditions for extended periods may affect device reliability. 4 General Electrical Specifications DC Operating Parameters TA = -40 C to 140 C, VDD = 5V (unless otherwise specified) Parameter Symbol Supply Voltage Vdd Supply Current Idd Output Current Capability Iout output @ low pressure Vout output @ full scale pressure Vout Low Clamping level Vout High Clamping level Vout Linearity error Vout Ratiometricity error Vout Programming Supply Vcc prog Zapping Supply Vzap Zapping Temperature Tzap Lifetime Power-up time Power-up time Response time 0% / 63% Trp Response time 10% / 90% Trp 10 - 90 Stabilization time Ts Pressure accuracy Table 2: Electrical specifications Test Conditions Operating Vdd = 5 V 10% , excluding output current Vdd = 5 V Vdd = 5 V Vdd = 5 V Min Typ 4.5 5 4 7 1 0.46 0.5 4.46 4.5 6.5 91 -0.5 -0.3 10 15.5 - 20 15 3.5 5 1 1.5 3 Max Units 5.5 V 10 mA mA 0.54 V 4.54 V 8.5 % Vod 93.5 % Vod 0.5 % Vod 0.3 % Vod 10.5 V 16 V o C 100 Year ms ms ms ms ms 1 % FS o o T = 0 C ... 85 C o o T < 0 C or T > 85 C o o 3901090808 Rev 001 Page 3 of 8 Data Sheet Feb 08 MLX90808 Absolute Integrated Pressure Sensor 5 Diagnostic features DC Operating Parameters TA = -40oC to 140oC, VDD = 5 V (unless otherwise specified) Parameter Symbol Output when sensor is broken Output when Vdd is broken Output when Vdd is broken Output when Vss is broken Output when Vss is broken Table 3: Diagnostic features Test Conditions Sensor broken Pull up > 4k7 Pull down Pull down > 10k Pull up Min Typ Max 2 4 0 Units % Vdd % Vdd % Vdd % Vdd % Vdd 96 100 6 Detailed General Description This chip integrates a pressure sensor and the associated signal conditioning on the same die. The supply voltage VDD directly supplies the pressure sensor. The pressure sensing element consists of a square diaphragm realized in the silicon chip by backside etching. Due to its small thickness this diaphragm reacts to a pressure difference at both of its side by cambering. The internal strain increases, in particular at the border of the diaphragm. Here, the piezoresistive elements have been implanted into the silicon diaphragm, which act as transducer. The piezo-resistive elements react to pressure induced changes of strain by changes in their resistance. Four resistors are placed at all four borders of the square diaphragm. They are arranged in a Wheatstone-bridge. A chopped instrumentation stage amplifies the differential output signal of the sensor. The gain of this amplifier can be adjusted with 3 bits. After the input stage, there is a 3 bit programmable coarse offset which is followed by a differential to single-ended conversion. The reference voltage for this stage is generated by a 10 bit DAC and varies linearly with temperature in order to perform the offset and offset drift compensation. A digital hardware multiplier calculates this compensation. The temperature signal, serving as input for this multiplier, is generated from the ADC of the output signal of the internal temperature sensor. The chopped signal is demodulated with a switched capacitor stage. The buffered output serves as reference for a 10 bit DAC to perform the span and span drift compensation. The DAC is controlled by the digital part. Finally the signal is given out by a class AB rail-to-rail amplifier capable of sourcing and sinking large currents. A 3-point temperature and 2-point pressure calibration is required (room temperature, a low temperature and a high temperature), to achieve an error less than 1% over the complete pressure and temperature range (the output error is referred to the output span). PTC (Programming Through Connector) protocol is used to perform calibration. The programming of the sensor chip is carried out via the analog connections (i.e. supply, ground, signal out). No additional pins are necessary for calibration. The output circuit is protected against short circuit to GND, Vbat (16V) and Vdd. 3901090808 Rev 001 Page 4 of 8 Data Sheet Feb 08 MLX90808 Absolute Integrated Pressure Sensor 7 Unique Features Diagnostic Limits Diagnostic of broken sensor: The output will be forced to ground (or a very low level) when the sensor membrane breaks. Diagnostic of broken wires: The output will be forced to ground (or a very low level) when the supply wire breaks, even when a pull-up is still connected to the output pin. The output will be forced to the supply voltage (or a very high level) when the ground wire breaks, even when a pull-down is still connected to the output pin. Output Protection The output is protected against short-circuits at either battery terminals. The output can handle voltages between -0.5V and 16V (independent of supply voltage). Memlock Function The memory consists of ZAP cells. When all calibration parameters are programmed, the chip can be locked. This to avoid unwanted that data be written into the memory cells. Once the chip is locked in a normal application, we can not read the zap contents and it is not possible to unlock afterwards, unless the MOW pin is used. This can be done by apply a supply between 2.5V and 3.5V on the MOW pin, then we can read back the content of the memory cells and zap another cell if necessary. Clamping Levels The user can enable the clamping of the output to ensure that the output can not enter the fault band in normal application. 8 Application Information 47nF 47nF Very few off-chip components are needed (only 2 decoupling capacitors, not higher than 100 nF). Only 3 pins are used (Vdd, Vss, Out), see pad layout drawing in paragraph 9. Calibration and Programming is made through the OUT pin. 3901090808 Rev 001 Page 5 of 8 Data Sheet Feb 08 MLX90808 Absolute Integrated Pressure Sensor 9 Programming and Calibration 9.1 Programming of the Temporary Memory of 90808 The temporary memory consists of a shift register of flip flops. It is used to search for the correct calibration settings. Mode 1 (TC[5:0]=01h) is used for this purpose. Afterwards these settings can be put in the permanent memory. The programming is done through the connector: you only need the application pins (supply, ground and output). You can enable the programming by forcing the supply high enough (VCC_T). You can input the data through the OUT pin. The data is Pulse Width modulated. At the end of the programming, we keep OUT high until VCC has reached his normal level (VCC_N). Thereafter we disconnect OUT. It is not necessary to do a power-down before the next settings are programmed. Timings 3901090808 Rev 001 Page 6 of 8 Data Sheet Feb 08 MLX90808 Absolute Integrated Pressure Sensor 9.2 Zapping of the 90808 The permanent memory of the 90808 is built with zap cells. The data output of an unprogrammed zap cell is 0. The data output is 1 when the cell is zapped. It is not possible to reprogram a zap cell to 0. Only 1 bit can be zapped at a time. You should use the normal mode (TC[5:0]=00h) and program 1 bit to '1' in the temporary memory. Afterwards you need to increase the supply voltage (VCC_Z) to be able to zap the bit. The zapping starts when OUT goes high (OUT_Z). There will flow a high current of approximately 200mA during the zapping. The memlock-bit should be zapped as last bit, because it disables the programming. The zap cells can also be read out by using mode 5 (TC[5:0]=05h). One bit should be set to 1 in the temporary memory. The supply current should be measured at the normal supply voltage. A low current (ICC_R0) indicates that the zap cell is not programmed. A high current (ICC_R1) indicates that the zap cell is programmed. 3901090808 Rev 001 Page 7 of 8 Data Sheet Feb 08 MLX90808 Absolute Integrated Pressure Sensor 10 Disclaimer Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. Melexis makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Melexis reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with Melexis for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical lifesupport or life-sustaining equipment are specifically not recommended without additional processing by Melexis for each application. The information furnished by Melexis is believed to be correct and accurate. However, Melexis shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of Melexis' rendering of technical or other services. (c) 2005 Melexis NV. All rights reserved. For the latest version of this document, go to our website at www.melexis.com Or for additional information contact Melexis Direct: Europe, Africa, Asia: Phone: +32 1367 0495 E-mail: sales_europe@melexis.com America: Phone: +1 603 223 2362 E-mail: sales_usa@melexis.com ISO/TS 16949 and ISO14001 Certified 3901090808 Rev 001 Page 8 of 8 Data Sheet Feb 08 |
Price & Availability of MLX90808LUF-2
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |